A modern architect can not design high performance computer architecture without thinking all factors of performance from hardware level (logic/layout design) to system level (application programs, operating systems, and compilers). For computer architecture design, there are few practical CAD tools, which support design activities of the architect. In this paper, we propose a CAD tool, called COACH, for computer architecture design. COACH supports architecture design from hardware level to system level. To make a high-performance general purpose computer system, the architect evaluates system performance as well as hardware level performance. To evaluate hardware level performance accurately, logic/layout synthesis tools and simulator are used for evaluation. Logic/layout synthesis tools translate the architecture design into logic circuits and layout pattern and simulator is used to get accurate information on hardware level performance which consists of clock frequency, the number of transistors, power consumption, and so on. To evaluate system level performance, a compiler generator is introducd. The compiler generator generates a compiler of a programming language from the desripition of architecture design. The designed architecture is simulated in the behavior level with programs compiled by the compiler, and the architect can get information on system level performance which consists of program execution steps, etc. From both hardware level performance and system level performance, the architect can evaluate and revise his/her architecture, considering the architecture from hardware level to system level. In this paper, we propose a new design methodology which uses () logic/layout synthesis tools and simulators as tools for architecture design and () a compiler generator for system level evaluation. COACH, a CAD system based on the methodology, is discussed and a prototype of COACH is implemented. Using the design methodology, two processors are designed. The result of the designs shows that the proposed design methodology are effective in architecture design.

Providing various assistances for design modifications on HDL source codes is important for design reuse and quick design cycle in VLSI CAD. Program slicing is a software-engineering technique for analyzing, abstracting, and transforming programs. We show algorithms for extracting/removing behaviors of specified signals in VHDL descriptions. We also describe a VHDL slicing system and show experimental results of efficiently extracting components from VHDL descriptions.

To transfer a small number, we inherently need a small number of bits. However all bit lines on a data bus change their status and redundant power is consumed. To reduce the redundant power consumption, we introduce a concept named active bit. In this paper, we propose a power reduction scheme for data buses using active bits. Suppressing switching activity of inactive bits, we can reduce redundant power consumption. We propose various power reduction techniques using active bits and the implementation methods. Experimental results illustrate up to 54.2% switching activity reduction.

The problem of synthesizing a minimum-cost logic network is formulated for a genetic algorithm (GA). When benchmarked against a commercial logic synthesis tool, an odd parity circuit required 24 basic cells (BCs) versus 28 BCs for the design produced by the commercial system. A magnitude comparator required 20 BCs versus 21 BCs for the commercial system's design. Poor temporal performance, however, is the main disadvantage of the GA-based approach. The design of a hardware-based cost function that would accelerate the GA by several thousand times is described.

Low Power design has emerged as a both practically and theoretically attractive theme in modern LSI system design. This paper presents system level power optimization techniques. A brief survey of system level low power design approaches and several examples in detail are described. It reviews some techniques that have been proposed to overcome the power issue and gives guideline for prospective system level solutions.

External pins for tests are precious hardware resources because this number is strongly restricted. Cores are tested via test access mechanisms (TAMs) such as a test bus architecture. When cores are tested via test buses which have constant bit widths, test stimuli and test responses for a particular core have to be transported over these test buses. The core might require more widths for input and output than test buses, and hence, for some part of the test, the TAMs are idle; this is a wasteful usage of the TAMs. In this paper, an optimization method of test accesses with a combined BIST and external test (CBET) scheme is proposed for eliminating the wasteful usage of test buses. This method can minimize the test time and eliminate the wasteful usage of external pins by considering the trade-off between test time and the number of external pins. Our idea consists of two parts. One is to determine the optimum groups, each of which consists of cores, to simultaneously share mechanisms for the external test. The other is to determine the optimum bandwidth of the external input and output for the external test. Our idea is basically formulated for the purpose of eliminating the wasteful external pin usage. We make the external test part to be under the full bandwidth of external pins by considering the trade-off between the test time and the number of external pins. This is achieved only with the CBET scheme because it permits test sets for both the BIST and the external test to be elastic. Taking test bus architecture as an example, a formulation for test access optimization and experimental results are shown. Experimental results reveal that our optimization can achieve a 51.9% reduction in the test time of conventional test scheduling and our proposals are confirmed to be effective in reducing the test time of system-on-a-chip.

This paper proposes two techniques for improving the accuracy of gate-level power analysis for system-on-a-chip (SoC). (1) Creation of custom wire load models for clock nets. (2) Use of layout information (actual net capacitance and input signal transition time). The analysis time is reduced to less than one three-hundredth of the transistor-level power analysis time. Error is within 5% against a real chip, (the same level as that of the transistor-level power analysis), if technique (2) is used, and within 15% if technique (1) is used.

System LSI is a new principal product of semiconductor industry and also a key component of Information Technology (IT). Design of a system LSI contains two different characteristics, system design and LSI design. It is keen issue to establish a design methodology of system LSIs in which designers have much freedom on their design from system level to device level and also can control various design parameters to optimize their design. In this paper, considerations on markets of system LSIs and requirements from each application are summarized. Some proposals on new directions of design methodology are also surveyed.

We propose a novel approach for designing a low power datapath in wireless communication systems. Especially, we focus on the digital FIR filter. Our proposed approach can reduce the power consumption and the circuit area of the digital FIR filter by optimizing the bitwidth of the each filter coefficient with keeping the filter calculation accuracy. At first, we formulate the constraints about keeping accuracy of the filter calculations. We define the problem to find the optimized bitwidth of each filter coefficient. Our defined problem can be solved by using the commercial optimization tool. We evaluate the effects of consuming power reduction by comparing the digital FIR filters designed in the same bitwidth of all coefficients. We confirm that our approach is effective for a low power digital FIR filter.

This paper presents a novel system-level design methodology, called quality-driven design, by which application-specific optimization can be achieved; furthermore the entire functionality can be shared to maximize design reuse. As a case of study, this paper focuses on quality-driven design for video applications and introduces an output quality adaptive approach based on variable bitwidth optimization to explore a new design space. MPEG2 video is used as the driver application to illustrate the potential of the presented methodology. Experimental results show the effectiveness of the methodology.

Entire systems on a chip (SOCs) embodying a processor, memory, and system-specific peripheral hardware are now an everyday reality. The current generation of SOC designers are driven more than ever by the need to lower chip cost, while at the same time being faced with demands to get designs to market more quickly. It was to support this new community of designers that we developed Satsuki-an integrated processor synthesis and compiler generation system. By allowing the designer to tune the processor design to the bitwidth and performance required by the application, minimum cost designs are achieved. Using synthesis to implement the processor in the same technology as the rest of the chip, allows for global chip optimization from the perspective of the system as a whole and assures design portability. The integral compiler generator, driven by the same parameters used for processor synthesis, promotes high-level expression of application algorithms while at the same time isolating the application software from the processor implementation. Synthesis experiments incorporating a 0.8 micron CMOS gate array have produced designs ranging from a 45 MHz, 1,500 gate, 8-bit processor with a 4-word register file to a 31 MHz, 9,800 gate, 32-bit processor with a 16-word register file.

In this paper we propose a co-design method for control systems using combination of models. By co-design," we mean a cooperative design method in which the behavior of the entire system is simulated as a single model while parameters of the system are being optimized. Our co-design method enables the various subsystems in the system, which have been designed independently as tasks assigned to different designers in the traditional design method, to be designed simultaneously in a unified cooperative way from the system-wide perspective of a system designer. Our proposed method combines models of controlling and controlled subsystems into a single model for the behavior of the entire control system. After the optimum control conditions are determined through simulation of the combined models, based on the corresponding algorithms and parameters, ASIC design proceeds quickly with accurate verification using iterative replacements of the behavior model by the electronic circuit model. To evaluate the proposed method, we implemented a design environment. We then applied our method to the design of ASICs in three test cases (in a control system and in audio-visual systems) to investigate its effectiveness. This paper introduces the concepts of the proposed co-design method, the design environment and the experimental results, and points out the new issues for system design.

This paper presents a variable pipeline depth processor, which can dynamically adjust its pipeline depth and operating voltage at run-time, we call dynamic pipeline and voltage scaling (DPVS), depending on the workload characteristics under timing constraints. The advantage of adjusting pipeline depth is that it can eliminate the useless energy dissipation of the additional stalls, or NOPs and wrong-path instructions which would increase as the pipeline depth grow deeper in excess of the inherent parallelism. Although dynamic voltage scaling (DVS) is a very effective technique in itself for reducing energy dissipation, lowering supply voltage also causes performance degradation. By combining with dynamic pipeline scaling (DPS), it would be possible to retain performance at required level while reducing energy dissipation much further. Experimental results show the effectiveness of our DPVS approach for a variety of benchmarks, reducing total energy dissipation by up to 64.90% with an average of 27.42% without any effect on performance, compared with a processor using only DVS.

This paper presents a novel low-energy memory design technique based on variable analysis for on-chip data memory (RAM) in application-specific systems, which called VAbM technique. It targets the exploitation of both data locality and effective data width of variables to reduce energy consumed by data transfer and storage. Variables with higher access frequency and smaller effective data width are assigned into a smaller low-energy memory with fewer bit lines and word lines, placed closer the processor. Under constraints of the number of memory banks, VAbM technique use variable analysis results to perform allocating and assigning on-chip RAM into multiple banks, which have different size with different number of word lines and different number of bit lines tailored to each application requirements. Experimental results with several real embedded applications demonstrate significant energy reduction up to 64.8% over monolithic memory, and 27.7% compared to memory designed by memory banking technique.

In this paper, we discuss on accuracy of power dissipation medels for CMOS VLSI circuits. Some researchers have proposed several efficient power estimation methods for CMOS circuits. However, we do not know how accurate they are because we have not established a method to compare the estimated results of power consumption with power consumption of actual VLSI chips. To evaluate the accuracy of several kinds of power dissipation models in chip-level, block-level and gate-lebel etc., we have been (i) Measuring power consumtion of actual microprocessors, (ii) Estimating power consumption with several kinds of power dissipation models, and (iii) Comparing (i) with (ii). The experimental results show as follows: (1) Power estimation at gate level is accurate enough. (2) Estimating power of a clock tree independently makes estimation more accurate. (3) Area of each functional block is a good approximation of load capacitance of the block.

The datapath width of a core processor has a strong effect on cost, power consumption, and performance of an embedded system integrated with memories into a single-chip. However, it is difficult for designers to appropriately determine the datapath width for each application because of the limited reusability of software and the lack of compilation techniques. The purpose of this paper is to clarify supports required from software for the optimal datapath width determination. As a solution, an embedded programming language, called Valen-C, and a retargetable Valen-C compiler are proposed. In this paper, the syntax and semantics of Valen-C along with the mechanism of the Valen-C retargetable compiler and how to preserve the accuracy of computation of programs in relation to various datapath widths are also described. Experiments with practical applications show that the total cost of the system including a core processor, ROM, and RAM is drastically reduced with little performance loss by reducing the datapath width.

In many embedded systems, a significant amount of power is consumed for off-chip driving because off-chip capacitances are much larger than on-chip capacitances. This paper proposes instruction scheduling techniques to reduce power consumed for off-chip driving. The techniques minimize the switching activity of a data bus between an on-chip cache and a main memory when instruction cache misses occur. The scheduling problem is formulated and two scheduling algorithms are presented. Experimental results demonstrate the effectiveness and the efficiency of the proposed algorithms.

A multi-application smart card system consists of an issuer, service vendors and cardholders, where cardholders are recipients of smart cards (from the issuer) to be used in connection with applications offered by service vendors. Authentic post-issuance program modification is necessary for a multi-application smart card system because applications in the system are realized after the issuance of a smart card. In this paper, we propose a system where only authentic modification is possible. In the proposed system, the smart card issuer stores a unique long bitstring called PID in a smart card. The smart card is then given to the cardholder. A unique substring of the PID (subPID) is shared between the cardholder and a corresponding service vendor. Another subPID is shared between the issuer and the cardholder. During program modification, a protocol using the subPIDs, a one-way hash function and a pseudorandom number generator function verifies the identity of the parties and the authenticity of the program.